Back to Blog
Vcds Rns-D Phone Preparation5/7/2021
For a better experience, please enable JavaScript in your browser before proceeding.Both charger (5NA980611) and two-way amplifier (4N0035456) are connected as follows: - Antenna cabling between charger, signal booster and roof aerial.
![]() Power from fuse 16 for both devices - Shared ground - Closed databus between Qi charger, signal amplifier and discover pro. Unfortunately it doesnt have any nice stuff for when you use your phone without RSAP (which I usually do), and i couldnt order both from the factory. Thats why im retrofitting the basiccomfort Phone preparation as well. Seeing as both devices im adding are only connected to the Discover pro and not to the gateway, the only coding I need to do (I assume) is in the 5F unit. I only found 1 bit regarding wireless charging availability, installedin the experimental coding for the 5F unit. Vcds Rns-D Phone Preparation Code Maybe SomebodyIs there anything else i need to code Maybe somebody has an autoscan of the 5F unit with the comfort Phone kit installed and also a Discover pro Gen 2 Autoscan below. Thanks. ![]() Address 03: ABS Brakes (J104) Labels:. Q0-907-379-IPB-V1.clb. Address 42: Door Elect, Driver (J386) Labels: 5QX-959-X93-42.clb. Address 52: Door Elect, Pass. J387) Labels: 5QX-959-X92-52.clb. Address A5: Frt Sens. Drv. Assist (R242) Labels: 3Q0-980-65X-A5.clb. End----------(Elapsed Time: 02:34, VBatt startend: 12.5V12.5V)-----------. Edit: As in; the infotainment unit doesnt give a charge notice on the screen. Does anybody have the long coding and an adaptation channel map of the 5F unit from a Tiguan with comfort telephone installed (PR-9IH or PR-9IJ) Would have to be an admap with VCDS 17.10 unfortunately. This one: IDE11524-ENG142161-Vehicle function list BAP 2nd generation: expansion-wirelesscharging0x48msgbus,not activated,192 (this one has about 20 possible options) Is probably the problem. Possible values include: Comfort Can Suspension Can Infotainment Can Extended Can Flexray Bus MIBCAN KombiCAN HybridCAN Comfort 2 Can CAB01 through CAB-29 etc. The charging unit is hooked up according to the factory diagram to pins 5 and 11 of the gray connector on the MIB2 unit. But I have no way of determining the correct setup of that channel when a device is hooked up to t12g5 and t12g11. Unfortunately there are zero autoscans to be found of MQB vehicles made with VCDS 17.10, and earlier versions dont show the necessary adaptation channels. Tried every combination i could think of, even turning on node 0x48 in the CAN gateway, but zero effect. I also couldnt find any channel to maybe see which pins are what or diagnose all databus connections of the MIB2, and I dont even know if the charge module is supposed to be showing up on an autoscan (no communication with that module anyway). So pulled the fuse and going to try again when there is more data available. PR codes PR-9IH9IJ. In the case of a Tiguan AD, you will need: - Center console (which has a slot for the charging interface) 5NB863241D suffix RM5 of 82V (dealer can tell you which color you have) (LHD model) - Phonecharging interface 5NA980611 - Two-way amplifier 4N0035456 and two plastic fasteners N90536901 - Contact housing amplifier 8E0971832 - Contact housing phone interface 4B0971978B - Contacts for both contact housings and the pins that go into the MIB unit are the same.
0 Comments
Read More
Leave a Reply. |